After being inspired by the santy blue tutorial for the door handles, I thought about some more areas that could use the added light.
This tutorial is to add lights to the storage space under the stereo and the change tray under the ashtray in my 2004 Santa Fe GL.
Materials needed:
4 LED's of your colour choice, with resistors to use with 12V power (check ebay)
Any 20-22 gauge wire you want as long as there are 2 wires in the strand (one for +, one for -)
3 HDD power wire "Y" adaptors (for pc's)
Tap-in Wire connectors
soldering skills and tools
Drill
Patience
The first step is to get the two pieces of the centre console out. (duh)
Pull out the ashtray and remove the 2 screws that it hides. Carefully pull out the lower half with the AC controls and disconnect the cables from the back. There is your first piece.
Next, remove the 2 screws from the bottom of the second part of the console,
and just pull it straight towards you gently and disconnect all of the cables from the fog lights, hazard lights, clock and defrost. Now you have your second piece.
You are going to have to do some prep work on the Y adaptors. If you look at the pins, either male or female, the pins are held in by a piece sticking further out the side of the pin. Basically a backstop. You will be removing the yellow wire and one of the black wires. Using a pushpin/thumbtack, gently push the piece into the pin on both sides. Save the leads that you remove, you will be using them later.
You should now be left with 3 of these...
Put one aside the way it is. Now cut the 2 female ends on each of the remaining adaptors off (so you should have removed 4 in total). Basically what you jut done is created a custom wire harness, and this can be developed for any application you want to use.
Now for the soldering part. Take your LED and a resistor. You will be attaching the resistor to the Anode of the LED, which is also the + lead.
Once you have the LED and resistor together, attach wire leads to them of sufficient length (about 3-4 inches). Put some heat shrink tubing around the leads and you should have this (I dremel the end of the LED flat to act as a diffuser) You will need to make 4 LED/Resistors with leads.
Now attach the ends of you LED leads to the bare ends of one side the Y adaptor (making sure that you remember which is + and which is -. Easy tip, black/grey should always be -, colours should be +.
Easy way to test if they are working, open up your pc and plug them into one of the power cords. Make the second set longer as they will be going into the upper part of the console, my leads were about 12-15 inches long.
Let's start with the basics here. Take the AC Controls, you will be drawing power from the wires that power up the bulb in the ashtray. I have marked which one is + and which is - to make things easy. Green is +, black is -.
Remember those bare leads I told you to keep, get a yellow and a black one. Using the Tap-in Connectors, attach the yellow lead to the + wire and the black to the negative wire.
There is the second part of your harness.
Now to place the LED's...
Remove the metal bracket that holds the ashtray so you have an unobstructed area. (disregard the extra wires coming out of the bottom, you won't have 'em, they are for the control box for my dash neons)
I placed my LEDs on the same side, all you have to do is drill inwards at about a 45 degree angle to make the mounting hole for your LED.
Wedge your LED's in the hole and throw in some hot glue for good measure. You should bend your leads so that they lie flat and are not in the way of anything.
You are finished with that part of the console, time for the second part.
Remove the tray by taking out the four screws holding it in.
Same drilling as with the lower part of the console, 45 degree down angle (and towards the back, trust me).
Do one on each side, glue the LEDs in and tape your leads to the tray to help control the wires.
Now you are really done, put everything back together, plugging all the harnesses back in. Reassembly is just the reverse.
Do be careful when you put the lower part back in that none of your new wires are dangling under the ashtray, just tuck them inside the console before you push it back in into place.
Here is what I was left with.....
I am more than likely going to be moving the LED's farther back in the upper part as they tend to illuminate alot of the cabin as well (that is the 2 blue lines you see on the console to the right and left of the opening.
I will be posting the second part for how to get the fog light switches blue as well at a later date...
Good luck
Spawn
"the universe has a way of balancing itself"
Edited by twospirits: Added missing pics from Hyundai Webtech and the LED pic.
This tutorial is to add lights to the storage space under the stereo and the change tray under the ashtray in my 2004 Santa Fe GL.
Materials needed:
4 LED's of your colour choice, with resistors to use with 12V power (check ebay)
Any 20-22 gauge wire you want as long as there are 2 wires in the strand (one for +, one for -)
3 HDD power wire "Y" adaptors (for pc's)
Tap-in Wire connectors
soldering skills and tools
Drill
Patience
The first step is to get the two pieces of the centre console out. (duh)
Pull out the ashtray and remove the 2 screws that it hides. Carefully pull out the lower half with the AC controls and disconnect the cables from the back. There is your first piece.
Next, remove the 2 screws from the bottom of the second part of the console,
and just pull it straight towards you gently and disconnect all of the cables from the fog lights, hazard lights, clock and defrost. Now you have your second piece.
You are going to have to do some prep work on the Y adaptors. If you look at the pins, either male or female, the pins are held in by a piece sticking further out the side of the pin. Basically a backstop. You will be removing the yellow wire and one of the black wires. Using a pushpin/thumbtack, gently push the piece into the pin on both sides. Save the leads that you remove, you will be using them later.
You should now be left with 3 of these...
Put one aside the way it is. Now cut the 2 female ends on each of the remaining adaptors off (so you should have removed 4 in total). Basically what you jut done is created a custom wire harness, and this can be developed for any application you want to use.
Now for the soldering part. Take your LED and a resistor. You will be attaching the resistor to the Anode of the LED, which is also the + lead.
Once you have the LED and resistor together, attach wire leads to them of sufficient length (about 3-4 inches). Put some heat shrink tubing around the leads and you should have this (I dremel the end of the LED flat to act as a diffuser) You will need to make 4 LED/Resistors with leads.
Now attach the ends of you LED leads to the bare ends of one side the Y adaptor (making sure that you remember which is + and which is -. Easy tip, black/grey should always be -, colours should be +.
Easy way to test if they are working, open up your pc and plug them into one of the power cords. Make the second set longer as they will be going into the upper part of the console, my leads were about 12-15 inches long.
Let's start with the basics here. Take the AC Controls, you will be drawing power from the wires that power up the bulb in the ashtray. I have marked which one is + and which is - to make things easy. Green is +, black is -.
Remember those bare leads I told you to keep, get a yellow and a black one. Using the Tap-in Connectors, attach the yellow lead to the + wire and the black to the negative wire.
There is the second part of your harness.
Now to place the LED's...
Remove the metal bracket that holds the ashtray so you have an unobstructed area. (disregard the extra wires coming out of the bottom, you won't have 'em, they are for the control box for my dash neons)
I placed my LEDs on the same side, all you have to do is drill inwards at about a 45 degree angle to make the mounting hole for your LED.
Wedge your LED's in the hole and throw in some hot glue for good measure. You should bend your leads so that they lie flat and are not in the way of anything.
You are finished with that part of the console, time for the second part.
Remove the tray by taking out the four screws holding it in.
Same drilling as with the lower part of the console, 45 degree down angle (and towards the back, trust me).
Do one on each side, glue the LEDs in and tape your leads to the tray to help control the wires.
Now you are really done, put everything back together, plugging all the harnesses back in. Reassembly is just the reverse.
Do be careful when you put the lower part back in that none of your new wires are dangling under the ashtray, just tuck them inside the console before you push it back in into place.
Here is what I was left with.....
I am more than likely going to be moving the LED's farther back in the upper part as they tend to illuminate alot of the cabin as well (that is the 2 blue lines you see on the console to the right and left of the opening.
I will be posting the second part for how to get the fog light switches blue as well at a later date...
Good luck
Spawn
"the universe has a way of balancing itself"
Edited by twospirits: Added missing pics from Hyundai Webtech and the LED pic.
